|
Selective
Notching Metal Detector Higher Performance HP1030 with Range and
Higher Sensitivity LCD Display
MODEL:
Navigator III (HP-1030)
One
of the newest top of the line high tech metal detectors. Fully
loaded with all the popular features. Metal detector can be used
under Motion
and Non-motion Modes.
1.
Four Operating Modes:
Interchange
among 4 operating modes DISC, ALL METAL, AUTO-NOTCH and NOTCH.
Press MODE touch pad to change the operating modes
in following order: DISC -> ALL METAL -> AUTO-NOTCH ->
NOTCH -> DISC...... The operating mode displays at bottom left
corner of the LCD.
DISC
mode - Power up the machine, and it enters into DISC mode
automatically. In addition, the estimated depth of coin-sized
objects is indicated by the rectangular segment indicators on
the left side of the display. In this mode, the detector can eliminate
unwanted objects from detection among the categories on top of
the panel from left to right. DISC/NOTCH indicator shows detector's
current discrimination level, and an object's estimated depth
is indicated by the arrows at the top of the display. SENS shows
current sensitivity level. DEPTH read the estimated target depth.
Each time a target detected, DEPTH indicator will illuminate.
Adjusting
Target DISC Range Press ADJ to enter the machine into DISC range
setting status LCD displays "DISC/NOTCH" at bottom right
corner then press "+" to increase the level of discrimination,
and press "-" to decrease the level of discrimination.
ALL
METAL Mode - Press MODE pad to enter into ALL METAL mode.
In this mode, the machine emits only a monotone sound when finding
a target, and DEPTH indicates relative target signal strength.
The stronger the signal is, the louder the tone is. Pinpoint is
used to locate a coin-sized object precisely. To move the coil
above or near the target area, target will be found soon. Target
identification is useless in ALL METAL mode. To see target identification
and depth, please change the detector into relative motion mode.
NOTCH
Mode - To selectively eliminate one or several metals from
the categories, please select NOTCH mode. DISC/NOTCH indicator
shows current target discrimination level, and an object's estimated
identification is indicated by the arrows at the top of the
display. SENS shows current sensitivity level. DEPTH indicates
the probable target depth.
Adjusting
Target NOTCH Range. In NOTCH mode, press ADJ to enter into DISC/NOTCH
range setting status. LCD displays "DISC/NOTCH" at bottom
right corner Press + touch pad , and one press ENT to accept or
reject the corresponding metal category. Press + again, its right
(left) arrow will flash, then press ENT to accept or reject another
metal category which the current arrow pointing to. Same as the
others......
AUTO-NOTCH
Mode - In this mode, the detector eliminates trash metals
automatically and keep the detection for coins. Eliminated trash
metals include: Bottle caps, S-CAPS, IRON/FOIL, Pull Tab. An object's
estimated identification is indicated by the arrows at the top
of the display. SENS shows current sensitivity level. DEPTH indicates
the probable target depth.
2.
SEVERE GROUND CONDITIONS
Another
use for the Sensitivity Control is to reduce false detection signals
caused by severe ground conditions. Although the detector has
specially designed circuit to reduce the ground interference,
not all onditions in hunting field can be anticipated. Highly
magnetic soils found in mountainous can cause the detector to
emit tones when metal objects are not present. High saline content
soils and sands can sometimes cause the detector to false. If
the detector emits false, non-repeatable, signals, REDUCE THE
SENSITIVITY.
3.
MULTIPLE TARGETS
If
you think the deeper real treasure is under a shallower target,
reduce the sensitivity to eliminate the detection of the deeper
targets, in order to properly locate and identify the shallower
target.
4.
SURFACE ELIMINATION
Press
SURF ELIM to enter into or quit Surface Elimination mode. SURF
ELIM only works in motion mode. SURF ELIM can improve the accuracy
of detection result in soil with mass trash metal.
It restrains the signal from trash metal in soil surface layer,
and balance the signal from large target. But detector's sensitivity
is decreased in this mode.
|
